收藏本站
NMR Series
Isolated 1W Single Output DC/DC Converters
GENERAL CHARACTERISTICS
Parameter
Conditions
Min.
Typ.
Max.
Units
5V input types
110
Switching frequency
12V input types
15V input types
24V input types
160
90
80
kHz
TEMPERATURE CHARACTERISTICS
Parameter
Speci?cation
Storage
Case Temperature above ambient
Conditions
All output types
5V output types
All other output types
Min.
-40
-50
Typ.
33
28
Max.
85
130
Units
°C
Cooling
TOLERANCE ENVELOPES
Free air convection
NMR118
NMR113, NMR 114, NMR119, NMR120
All other types
l a
Lo
o Line
a lL o
+7%
+4.5%
+2%
V NOM
Typic
a
d L in e
0%
-2.5%
-5%
+4%
+2%
V NOM
T y pica l L
ad
+1%
-1%
-3%
+10%
+5%
V NOM
T y pi c
a d L
i n e
+2.5%
-2.5%
-7.5%
10
25
50
75
100
10
25
50
75
100
10
25
50
75
100
Output Load Current (%)
Output Load Current (%)
Output Load Current (%)
The voltage tolerance envelope shows typical load regulation characteristics for this product series. The tolerance envelope is the maximum output voltage variation due to
changes in output loading.
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a speci?ed time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NMR series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no speci?c agency approvals, such as the NMR series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NMR series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While
parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically
polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We
therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from speci?ed test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
RoHS COMPLIANCE INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300oC for 10 seconds. The pin termination ?nish
on this product series is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The series is backward compatible with Sn/Pb soldering
systems.
For further information, please visit www.murata-ps.com/rohs
www.murata-ps.com/support
KDC_NMR.E01 Page 2 of 5
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NMS1215C CONV DC/DC 2W 12VIN 15V DIP 6KV
NMT0572SC CONV DC/DC 3W 5VIN 24-48-72VOUT
NMV1515SAC CONV DC/DC 1W 15VIN 15VOUT SIP
NMV2415SC CONV DC/DC 1W 24VIN 15VOUT SIP
NMXD0515UC CONV DC/DC 5W 5VIN 15V DIP UNREG
NMXS1205SOC CONV DC/DC 5W 12VIN 5V DIP REG
NOJE687M004RWJ CAP NIOB OXIDE 680UF 4V 2917
NOJX686M006RWJ CAP NIOB OXIDE 68UF 6.3V 2917
相关代理商/技术参数
NMR11K5 制造商:NIC Components Corp 功能描述:
NMR12.70 制造商:NIC Components Corp 功能描述:
NMR120 功能描述:DC/DC转换器 1W ISOLATED 4P SIP RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
NMR120C 功能描述:DC/DC转换器 DC/DC TH 1W 24-15V RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
NMR120K 制造商:NIC Components Corp 功能描述:
NMR121K 制造商:NIC Components Corp 功能描述:
NMR124K 制造商:NIC Components Corp 功能描述:
NMR127.0 制造商:NIC Components Corp 功能描述: